Launch offer — valid today only

📄 Digital book in PDF · read it on your phone or print it

Your Compact Tractor, Illustrated: Hitch, PTO, Loader and Slopes, Always in the Same Order One Topic on Every Page

Controls, three-point hitch, PTO, front loader, ballast in kilograms, slopes, driveway grading, snow and maintenance through the Canadian year. Every topic has its own page: the drawing first, then what you need to remember. 70 illustrated pages.

YES, I WANT MY TRACTOR BOOK, ILLUSTRATED

🔒 Secure checkout · PDF by email · 30-day guarantee

Every topic, its own pageEach control and manoeuvre drawn, with the explanation beside it
70 illustrated pages9 sections, from your tractor part by part to your one-page safe operating sheet
Up-to-date sourcesCCOHS, the Canadian Agricultural Safety Association and ISO/ASABE hitch and PTO standards
PDF by emailFormat

Look Inside the Book

Every page has one big drawing and a box with the steps and numbers you need to know:

Ten parts, one drawing: engine to loader mounts, each labelled with its job
Ten parts, one drawing: engine to loader mounts, each labelled with its job
Loose sway lets a box blade hit the tires; snug chains keep a mower centred.
Loose sway lets a box blade hit the tires; snug chains keep a mower centred.
540 rpm = 9 turns per second: a loose sleeve is wrapped before you can react.
540 rpm = 9 turns per second: a loose sleeve is wrapped before you can react.
Forks cut safe capacity: load to the backrest, tilt back, travel low and slow.
Forks cut safe capacity: load to the backrest, tilt back, travel low and slow.
Before using a front loader, add the rear weight your manufacturer recommends.
Before using a front loader, add the rear weight your manufacturer recommends.
Rotary cutter: 92 m (300 ft) throw zone, replace damaged blades in pairs, never unclog while turning
Rotary cutter: 92 m (300 ft) throw zone, replace damaged blades in pairs, never unclog while turning
Service by engine hours: hour meter, your manual's chart, and a written log
Service by engine hours: hour meter, your manual's chart, and a written log

Swipe to see more →

These are real pages from the book. The table of contents is the full one: 9 parts and 66 topics.

The Problem Isn't You. It's How It Was Explained to You.

You're behind the tractor with a box blade sitting on the gravel. The lower arms won't line up with the pins, the top link is too long and the blade hangs crooked.

You open the operator's manual. The hitch is three paragraphs and a small diagram. Lift rods, top link, sway chains: names, but no picture of where each one goes.

540 rpm = 9 turns per second: a loose sleeve is wrapped before you can react.

In Compact Tractor Illustrated, the three-point hitch is one page. Lower arms, top link, lift arms, lift rods and sway chains, drawn as a triangle and labelled. You see which part does what.

The same goes for hitching step by step, setting the top link for a level implement, the PTO shields, carrying the loader low and the stability triangle: each one has its own drawn page.

You look, you understand, and you hitch it up. Next Saturday you do it without opening the manual.

COMPARE FOR YOURSELF

The Same Topic, Two Ways to Learn It

THIS
  • The manual: line after line
  • The walk-around explained only in words
  • You climb on still unsure
Prior to each period of operation, the operator shall conduct a visual inspection of the tractor and attached equipment. The inspection should include, but is not limited to, an examination of the ground beneath the machine for evidence of fluid leakage, verification of tire condition and inflation, confirmation of engine oil, coolant and hydraulic fluid levels, assessment of drive belt tension and wear, and confirmation that all hitch pins, retaining clips, PTO shields and lighting components are present, secure and functional before the engine is started.
FOR THIS
  • The walk-around in one drawing
  • The steps in a numbered box
  • You look and you get it
Loose sway lets a box blade hit the tires; snug chains keep a mower centred.
CONTENTS

Take a Look at the 9 Parts and 66 Topics

Meet your tractor, before you climb on, the three-point hitch, the PTO, the front loader, ballast and slopes, jobs on the acreage, maintenance through the Canadian year and quick checks: 70 pages, all illustrated.

IMeet Your Tractor · pp. 5-13
  1. Your Tractor, Part by Part
  2. Sub-Compact or Compact: What You Actually Have
  3. Hydrostatic or Gear Drive
  4. Every Lever and Pedal, Labelled
  5. The Dashboard Lights You Must Know
  6. 4WD and Diff Lock: When to Use Each
  7. ROPS Up, Seatbelt On
  8. Safety Interlocks: Why the Tractor Won't Start
  9. Tires: Ag, Turf and Industrial
IIBefore You Climb On · pp. 14-21
  1. The Daily Walk-Around, in Order
  2. Checking the Fluids
  3. Tire Pressure and Loose Lug Nuts
  4. Greasing: Where the Fittings Are
  5. Getting On and Off: Three Points of Contact
  6. The Start-Up Sequence
  7. The Shutdown Sequence
  8. Diesel Fuel and Keeping It Clean
IIIThe Three-Point Hitch · pp. 22-29
  1. The Three-Point Hitch, Part by Part
  2. Hitch Categories and Pin Sizes
  3. Hitching an Implement, Step by Step
  4. Unhitching Without a Fight
  5. Setting the Top Link for a Level Implement
  6. Sway Chains and Stabilizers
  7. Position Control and Draft Control
  8. Quick Hitch: Faster, With Limits
IVPTO: The Most Dangerous Shaft on the Farm · pp. 30-35
  1. What the PTO Does
  2. Shields and Guards That Stay On
  3. Entanglement: Seconds, Not Minutes
  4. Shaft Length and Overlap
  5. Engaging the PTO the Gentle Way
  6. Shear Bolts, Slip Clutches and the Overrunning Clutch
VThe Front Loader · pp. 36-43
  1. The Loader, Part by Part
  2. The Joystick: Four Moves Plus Float
  3. Carry It Low
  4. Reading the Loader Capacity
  5. Filling the Bucket Without Spinning
  6. Pallet Forks and Heavy Lifts
  7. Never Under the Loader, Never on It
  8. Taking the Loader Off and On
VIBallast, Stability and Slopes · pp. 44-52
  1. The Stability Triangle
  2. Why the Loader Needs Rear Ballast
  3. Working Out Ballast in Kilograms
  4. Ballast Options: Box, Wheel Weights, Filled Tires
  5. Wheel Spacing for More Stability
  6. Slopes: Up and Down, Never Across
  7. Loaded Bucket on a Hill: Heavy End Uphill
  8. Ditches, Banks and Soft Edges
  9. Towing From the Drawbar Only
VIIJobs on the Acreage · pp. 53-59
  1. Mowing Rough Grass With a Rotary Cutter
  2. Belly Mower and the Lawn
  3. Grading a Gravel Driveway With a Box Blade
  4. Crown and Ditches: Making Water Run Off
  5. Digging Post Holes Safely
  6. Tilling a Garden
  7. Clearing Snow: Bucket, Blade or Blower
VIIIOwner Maintenance Through the Canadian Year · pp. 60-67
  1. The Hour Meter and the Service Chart
  2. Changing the Engine Oil and Filter
  3. Air Filter: Inspect, Don't Overclean
  4. Hydraulic and Transmission Fluid
  5. Cold Starts: Block Heater and Battery
  6. Winter Diesel and Fuel Gelling
  7. Spring Start-Up Checklist
  8. Fall Storage Checklist
IXReview and Quick Checks · pp. 68-70
  1. The Ten Most Common Mistakes, Drawn
  2. When Something Sounds Wrong
  3. Your One-Page Safe Operating Sheet

One Page, One Topic, All Clear

Think of it this way:

It's Saturday. Your bucket is full of gravel and the driveway runs along the ditch bank. You need to know right now which way to point the tractor.

You open the page on a loaded bucket on a hill. The tractor is drawn on the slope with the heavy end uphill, and an arrow shows the way to drive: straight up or straight down, never across.

Before using a front loader, add the rear weight your manufacturer recommends.

The same with the stability triangle, rear ballast worked out in kilograms, the PTO shields, the start-up sequence and the fall storage checklist: each one on its own page.

Compact Tractor Illustrated is 70 pages in 9 sections, all drawn, and it ends with the ten most common mistakes and a one-page safe operating sheet.

What you see drawn, you don't have to memorize.

What's Inside Compact Tractor Illustrated:

Ipp. 5-13

Meet Your Tractor

Every part of the tractor, sub-compact or compact, hydrostatic or gear drive, each lever and pedal, the dashboard lights, 4WD and diff lock, ROPS, interlocks and tires.

IIpp. 14-21

Before You Climb On

The daily walk-around in order, fluids, tire pressure and lug nuts, grease fittings, three points of contact, the start-up and shutdown sequences and clean diesel.

IIIpp. 22-29

The Three-Point Hitch

Hitch any implement without fighting the pins: the hitch part by part, categories and pin sizes, hitching and unhitching step by step, levelling with the top link, sway chains, position and draft control, quick hitch.

IVpp. 30-35

PTO: The Most Dangerous Shaft on the Farm

What the PTO does, shields that stay on, entanglement, shaft length and overlap, engaging it gently, shear bolts and clutches.

Vpp. 36-43

The Front Loader

The loader part by part, the joystick and float, carrying it low, reading the capacity, filling the bucket, pallet forks, never under it, taking it off and on.

VIpp. 44-52

Ballast, Stability and Slopes

Know which way to point the tractor on a bank: the stability triangle, rear ballast worked out in kilograms, ballast options, wheel spacing, slopes, a loaded bucket on a hill, ditches and banks, towing from the drawbar.

VIIpp. 53-59

Jobs on the Acreage

Rotary cutter, belly mower, grading a gravel driveway, crown and ditches, post holes, tilling a garden and clearing snow.

VIIIpp. 60-67

Owner Maintenance Through the Canadian Year

Hour meter and service chart, oil and filter, air filter, hydraulic and transmission fluid, cold starts, winter diesel, spring start-up and fall storage.

IXpp. 68-70

Review and Quick Checks

The ten most common mistakes drawn, what to check when something sounds wrong and your one-page safe operating sheet.

At the end of the book: The ten most common mistakes drawn, a page for when something sounds wrong and a one-page safe operating sheet.

SHOW ME WHAT'S INSIDE

Plus: 2 Free Books

Spot the Hazard: Tractor Workbook

BONUS 1: «Spot the Hazard: Tractor Workbook»

Value on its own: US$ 17.90

Drawn scenes from a real acreage where you find what's wrong (loader too high, PTO shield missing, side slope, passenger on the fender), so the safe habit is automatic before you climb on.

Walk-Around & Common Mistakes Cards

BONUS 2: «Walk-Around & Common Mistakes Cards»

Value on its own: US$ 14.90

Printable quick cards with the daily walk-around in order and the most common mistakes drawn before/after, to pin up in the shop and check in one glance.

Compact Tractor Illustrated with 2 Free Books

  • Compact Tractor Illustrated: 70 illustrated pagesUS$ 63
  • BONUS 1: Spot the Hazard: Tractor WorkbookUS$ 17.90
  • BONUS 2: Walk-Around & Common Mistakes CardsUS$ 14.90
  • High-resolution PDF to printIncluded
Total value US$ 95.80
YOUR PRICE:
US$ 27
You save US$ 68.80
YES, I WANT COMPACT TRACTOR ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

Secure purchaseEncrypted payment30-day guarantee

PDF by email: We email you Compact Tractor Illustrated as a PDF, together with the two free books. It's a single payment: no installments, no extra charges.

Who This Book Is For

You've just bought your first compact tractor

You've just bought your first compact tractor

Every lever, pedal and dashboard light is drawn and labelled, so you know what each one does before you turn the key.

Your first season on the acreage is coming

Your first season on the acreage is coming

Hitch, PTO, loader and ballast in the order you'll use them, plus the spring start-up and fall storage checklists for the Canadian year.

You already use it every weekend

You already use it every weekend

One page to check the stability triangle, a slope or the service chart when you have a doubt, printed and kept in the shop.

Everything You Get Today

US$ 95.80US$ 27
YES, I WANT COMPACT TRACTOR ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.

30DAYS
GUARANTEE

30-Day Guarantee

Try Compact Tractor Illustrated for 30 days, bonus books included.

We refund everything if the file won't open, if the book isn't what you see here, if you were charged twice or if the email doesn't arrive. Just email us.

You pay once. No subscriptions.

Frequently Asked Questions

Is it for me if I've just bought my first compact tractor, or I've been using one for a while?

Yes. It starts with what each control does and goes up to ballast, slopes and maintenance. It works with any brand: it teaches the logic common to compact tractors, and the numbers for your own machine come from your operator's manual.

Where does the content come from?

It's checked against Canadian farm safety guidance (CCOHS, the Canadian Agricultural Safety Association and provincial farm safety resources) and the ISO/ASABE standards for the three-point hitch and PTO.

Is this official material?

No. It's an independent illustrated book, not affiliated with or endorsed by any safety body or tractor brand, and it doesn't come with a certificate. For hands-on training, ask your dealer or your provincial farm safety association.

Does it replace the operator's manual or hands-on training?

No. It's a reference to understand and remember. Your operator's manual, your dealer and hands-on safety training always come first.

Isn't all this already in my operator's manual or free on YouTube?

The information is out there, but spread across paragraphs and videos that each do it differently. Here every topic is one drawn page, always in the same order, so you find it quickly in the shed. The numbers for your own machine still come from your operator's manual.

When and how do I get it?

The book and the 2 gift books arrive as a PDF by email, at the address you enter at checkout.

Do I have to pay every month?

No. It's a one-time payment.

Can I have it on paper?

Yes. The PDF prints on regular letter paper, so you can keep it in the shop.

How does the refund work?

You have 30 days. We refund everything if the file won't open, if the book isn't what you see on this page, if you were charged twice or if the email doesn't arrive: just email us.

Before You Close This Page

No more rereading the manual without it sticking.

The three-point hitch: you see it drawn and that's it.

You head out to the shed knowing where everything is.

Drawings make studying faster.

The book is right below.

One-time payment: US$ 27 · Guarantee: 30 days · PDF by email

YES, I WANT COMPACT TRACTOR ILLUSTRATED FOR US$ 27

📄 This is a digital PDF book sent to your email: nothing is printed or shipped.